Bond-All Acrylic Primer is a high performance, environmentally friendly, multi-surface water based bonding primer. It provides outstanding adhesion to many "hard-to-paint" surfaces. These include interior and exterior silicone modified polyester (SMP) pre-coated steel, Kynar®, metal, wood, drywall, concrete, fiber cement, glass, vinyl, masonry, lacquered and previously painted surfaces, Bond-All is also a great barrier coat when applying high performance solvent coatings overtop previously painted surfaces. Very good solvent and chemical resistance.

PHYSICAL CHARACTERISTICS

PRODUCT USE

Suitable to prime a wide range of surfaces however because there are so many, plastics, composite materials and unique circumstances always test a small area first for adhesion and topcoat compatibility before starting. *When priming Kynar® and Silicone Polyester pre-finished metal at least two test patches in different areas is recommended to demonstrate adhesion that is acceptable to you. Glossy or smooth hard slick surfaces should be dulled and/or abraded using silicon carbide sandpaper, Scotch-Brite® or other abrading medium to de-gloss and create a surface profile to obtain maximum adhesion. Bare or rusting ferrous metal requires a rust inhibiting iron primer be applied 1st. Not recommended for use on polyethylene, polypropylene, Teflon® or Nylon. Not recommended for below grade or submersion application.

DIRECTIONS

GENERAL: All surfaces to be painted must be clean, dry and in fit condition to be painted. Be sure to remove all wax, silicone, oil, powdery or scaling rust, loose or peeling paint and all other foreign matter. Apply using conventional, airless or assisted-airless spray, brush or roller.

CONDITIONS: 40°F-100°F surface temperature and surrounding air. Do not apply in direct sun or when the temperature will fall below 35°F before it has thoroughly dried.

SPREADING RATE: (@ 3.5 mil wet / 1 mil dry, unreduced): 593 square feet per gallon theoretical with no loss and no reduction.

RECOMMENDED FILM THICKNESS: 1 mil (3.5 wet, unreduced). Adjust accordingly when reducing to insure minimum 1 mil dry.

BARE WOOD, DRYWALL OR MASONRY: Use Prime X4 instead.

GALVANIZED ALUMINUM SURFACES: All loose, powdery or scaling must be removed. Thoroughly clean all surfaces with Zap-It Chalk & Grime Buster to remove dirt, grease, oil, wax or other foreign matter.

PAINTED SURFACES: Be sure all loose and peeling paint is completely removed, and the surface is clean. Remove excess chalkiness by thoroughly cleaning the surface with Zap-It Chalk & Grime Buster . Glossy or smooth hard slick surfaces should be dulled and/or abraded using silicon carbide sandpaper, Scotch-Brite® or other abrading medium to de-gloss and create a surface profile to obtain maximum adhesion.

MIXING: Mix thoroughly before use and/or after thinning.

EFFECT OF FREEZING: Do Not Freeze! Product will not recover!

SHELF LIFE: Six months - Please rotate stock on a regular basis.

TINTING: Bond-All Primer can be tinted with up to 4 ounces of universal colorant

THINNING: Ready to spray as packaged, but if thinning is necessary, use water. Do not overthin; sagging may result.

APPLICATION: Apply using conventional application methods and equipment. DRY TIMES (@ 77°F) 50% RH: DRY-TO-TOUCH: 30—45 minutes; RECOAT with Water based coatings: 2 hours; RECOAT with solvent based materials: 4 hours. FULL CURE: 7-10 days.

CLEAN-UP: Clean spills and drips with warm soapy water. Do not allow splatters to dry. Clean applicators, brushes and rollers immediately after use with soapy water. Clean spray equipment immediately after according to manufacturer instructions. Dispose of unused product according to applicable local laws.

SHELF LIFE: Shelf Life is 3 years from the date of manufacture when stored at temperatures not exceeding 120°F.

NOTE: FOR USE BY PROFESSIONAL, TRAINED PERSONNEL, USING PROPER EQUIPMENT WITH STANDARD SAFETY PROCEDURES. NOT INTENDED FOR SALE TO THE GENERAL PUBLIC. FOR INDUSTRIAL USE ONLY. NOT FOR RESIDENTIAL USE.

Please read the MSDS before using this product.

HEALTH & SAFETY: Use in a well-ventilated area. Avoid contact with eyes. Wash hands thoroughly with soap and warm water after use. Do not take internally. When spraying or sanding use a properly fitted NIOSH approved respirator. WARNING! Scraping, sanding or removing old paint may release toxic lead dust which can lead to brain damage and serious illness especially in children and may affect fetal development. Find out how to protect yourself by contacting the National Lead Information Hotline at 1-800-424-LEAD or go to www.epa.gov/lead

FIRST AID: SKIN: Wash thoroughly with soap and warm water. EYES: Rinse eyes with clean water for 15 minutes. Seek medical attention. INHALATION: Use only in well ventilated areas. If irritation occurs move to fresh air and seek medical attention. INGESTION: Do not induce vomiting. Seek medical attention.

REGULATORY STATUS: This product is not considered a hazardous waste under current RCRA regulations. This product does not contain, nor is it manufactured using ozone depleting substances as listed under Section 611 of the Clean Air Act.

DO NOT TAKE INTERNALLY • USE ONLY WITH ADEQUATE VENTILATION

KEEP OUT OF REACH OF CHILDREN

NON-PHOTOCHEMICALLY REACTIVE - KEEP FROM FREEZING